- Position Front - Wheel Diameter/ISO 700C / 622 - Axle Type QR - Hub Spacing 100mm - Wheel-Brake Comp. Rim and Disc IS 6-bolt - Freehub Body - - Wheel Tire Type Clincher - Rim Material Aluminum - Rim Construction Double wall - Rim Internal Width 18.4mm - Rim inner width range 0-21.9mm - Rim Color Black - Rim Drilling 36 - Hub Model Shimano HB-M475 - Wheel Weight - - Spoke Type Stainless - Valve Schrader - Rim External Width 24.4mm - Depth 16mm - Rim Model Alex DM18 - Skewers Included Yes
Zipp Speed Weaponry Valve Extender Wrench Set - Two 4 mm and 5 mm combination wrenches - Replacement wrenches required to properly install Zipp integrated valve extenders - Use with Zipp Tangente tubes with aluminum Presta valve and aluminum valve extender
Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.
$8.00 - $40.00
Whisky’s tubeless rim tape is designed to make setup as easy as possible. Elasticity allows for smooth, even adherence while translucency lets you see where the tape contacts the rim. Different widths available to fit almost any rim.
$8.00 - $16.00
Whisky Parts Co. Tubeless Rim Tape.
- CNC-machined tubeless valves with aluminum stem nut and valve core wrench cap - Fit for most other tubeless rims and wheel
The Deadbolt Ultralight Thru-Axles are offered in a 6mm flat button head design, for a flush, clean look. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications - 6mm hex wrench required for installation
$125.00 - $143.00
High quality sealed bearing hub is available in traditional and modern configurations. - Steel axle, aluminum end caps with steel knurled contact surfaces - Same proven driver mechanism as higher priced models - Spoke Interface: J-Bend - Hub/Brake Compatibility: 6-Bolt Disc - Skewer Included: No - Bearing Type: Sealed Cartridge
$69.00 - $85.00
Whether your joy comes from barreling downhill, or tearing up to the top, SRAM's MTH 716 front hub will leave a smile on your face. An aluminum hubshell with machined flanges grant the hub a low weight without compromising durability. TPlus, tough cartridge bearings roll smooth for the long haul.
$394.00 - $526.00
It's a fact: On an E-MTB you run into trail sections much faster than you have ever before considered possible. The H 1700 SPLINE 30 has the power to get you out of such situations as a winner and not face down in the dirt. Steering precision is covered by the strong spokes and the trademark DT Swiss wheel build with high and even spoke tension. The rim can take tires suited for fast riding on rugged terrain and supports them perfectly, even at low pressures. Reliable Ratchet System hubs finally make sure that you can come back and attack those gnarly sections of trail time and time again.
$361.00 - $532.00
Just wide enough, just light enough. At 30mm internal rim width the M 1700 SPLINE 30 works for tires ranging from slightly wide to quite wide, allowing it to attack the hardest terrain. But with a high-end build, butted spokes, patented alloy Pro Lock nipples and the benchmark Ratchet System hubs, it still comes in at a low weight. Low weight means it's very reactive to rider input. Reactive means fun, and fun is why we are all doing this, right?
The PR 1600 SPLINE 32 is characterized by its super stiff yet lightweight medium-profile aluminum rim. The use of the PHR nipple system allows a very low weight. Stiffness is generated via the big cross-section and thanks to the 18mm internal width and the tubeless-ready design, it is ideally equipped for the use of modern road bike tires. The PR 1600 SPLINE 32 is a wheel that excels on any terrain, transfers every bit of energy into forward momentum, and takes every corner with Swiss precision.
When heavy duty cyclocross riding is your passion, the C 1800 is the right partner for any mission. With its high-end sleeved rim ready to take up MTB-sized rubber and the tough build featuring DT's sturdiest bladed spokes, it is right at home in anything from jumping obstacles to cutting through the mud to sprinting up steeps. Trademark DT Swiss reliability coming from the precision hubs and the superb wheel building quality guarantee trouble free rides year-in and year-out.
$565.00 - $776.00
With even the EWS race courses getting tougher and tougher and tire manufacturers offering Enduro-strong tires in 2.5-inch sizes, the demand from DT's pros for a wide, Enduro tough wheelset came up and DT responded by developing the EX 1501 SPLINE ONE 30. Often used as a front wheel to generate as much grip where you need it most, it is the wheel for those hunting after the toughest of tracks or those living right in the Alps. Strong, lightweight, and tough as nails, the EX 1501 30 is ready for just about anything.
$552.00 - $750.00
Responding to the demand from top racers for even wider rims, DT have developed an XC-specific 25mm-wide rim profile. This is what's built into the XR 1501 SPLINE ONE 25. The result is a super capable, super light Cross Country wheel. It feels perfectly at home on the trails that have become tougher and rougher both up and down the mountain. And built with DT Swiss quality in every detail, from the hub internals to the spoke nipple, it makes sure you complete all the laps, weekend after weekend.
$1,092.00 - $1,514.00
Our benchmark setting Aero+ rim matched to a punchy mix of top end aerolite and laced to premium Ratchet System hubs makes for a wheel that delivers in all riding situations. Fitting 28 mm tires on its wide rims will give you all the comfort and grip needed for extended rides on mixed surfaces. At the same time, in combination with 25 mm rubber, the ERC 1400 SPLINE with will aero optimize your race bike, ready for you to set your own, new benchmarks.
$223.00 - $289.00
At the core of this all-around wheelset lies a modern, wide, and light aluminium rim. Being the foundation of the wheel, it makes for a balanced width-to-stiffness-to-weight ratio. This rim is complemented by a hub featuring DT Swiss' proven pawl system freewheel as well as a high end build with bladed spokes and elaborate alloy nipples. These features make it a premium training wheel easily able to race your mates when the city limit sign comes up.
$348.00 - $519.00
Rainy days, wet soil, rocks and roots. The tubeless tires somehow find grip. The M 1700 SPLINE 25 comes stock with tubeless rim tape and valves, just the right tool for demanding trails. The wide rim gives the tire that decisive little bit more support while the Ratchet System freewheel ensures safe engagements even in the most averse conditions. Finally, being a lightweight helps you to quickly get back up to that trail entrance, to start the slip-and-grip fest all over again.
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
- Position Front - Wheel Diameter/ISO 27.5'' / 584 - Axle Type 20mm TA - Hub Spacing 110mm - Wheel-Brake Comp. Disc IS 6-bolt - Freehub Body - - Wheel Tire Type Tubeless Ready - Rim Material Aluminum - Rim Construction Double wall - Rim Internal Width 27mm - Rim inner width range 22-27.9mm - Rim Color Black - Rim Drilling 32 - Hub Model Novatec D881SB - Wheel Weight - - Spoke Type DT Champion - Valve Presta - Rim External Width 30mm - Depth 22mm - Rim Model Mavic EN427 Disc - Skewers Included No
- Position Rear - Wheel Diameter/ISO 27.5'' / 584 - Axle Type 12mm TA - Hub Spacing 150mm/157mm - Wheel-Brake Comp. Disc IS 6-bolt - Freehub Body Shimano HG - Wheel Tire Type Tubeless Ready - Rim Material Aluminum - Rim Construction Double wall - Rim Internal Width 25mm - Rim inner width range 22-27.9mm - Rim Color Black - Rim Drilling 32 - Hub Model Novatec DH82SB - Wheel Weight - - Spoke Type DT Champion - Valve Presta - Rim External Width 30.8mm - Depth 22mm - Rim Model Fratelli FX 25 XXX - Skewers Included No
$14.95 - $79.95
Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).
Zipp Speed Weaponry Freehub Bodies - Material: Aluminum
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows to fully tighten the axle and to perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Removable, plug-in lever design is streamlined and protects your RWS lever - Thread pitch: 12 x 1.5mm - Length: 121mm
- Position Front - Wheel Diameter/ISO 27.5'' / 584 - Axle Type QR - Hub Spacing 100mm - Wheel-Brake Comp. Rim - Freehub Body - - Wheel Tire Type Clincher - Rim Material Aluminum - Rim Construction Double wall - Rim Internal Width 19mm - Rim inner width range 0-21.9mm - Rim Color Black - Rim Drilling 36 - Hub Model Formula FM-21-QR - Wheel Weight - - Spoke Type Stainless - Valve Schrader - Rim External Width - - Depth 20mm - Rim Model Evo E-Tour 19 - Skewers Included Yes
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
Stan's 3.30/3.30Ti Hub Kit converts Stan's 3.30 front hubs from quick-release to through-axle compatible. Installation is easy—just pull the old ones off and put the new ones on. Conversion kits available in 12mm and 15mm.
Straight pull spokes and nipples from Zipp
Stan’s S1 wheelset line brings patented tubeless technology to an even wider range of riders. Built for long life, low maintenance, and outstanding value, the S1 series wheels feature 6061 series alloy rims and are available in six different widths suited to a wide range of tire sizes and riding styles. With an emphasis on value and durability, the S1 alloy wheelsets join a mountain wheel line-up that currently includes Stan’s successful MK3 premium alloy wheels and innovative Valor and Bravo carbon series wheelsets. While MK3 wheelsets are built to balance strength, light weight, and stiffness, S1 wheelsets focus on maximum strength and durability. The deeper profile and thicker walls of the S1 rims result in a 50-70g weight increase over MK3 rims, but offer greater impact strength for an even wider range of use. “The new S1 series wheels were developed from rims ridden in Redbull Rampage and raced on the World Cup DH circuit for years,” said Creative Director, Chris Currie. “The goal was to take everything we’ve done for tubeless technology, and put it into a truly bombproof and affordable wheel.” Designed according to Stan’s WideRight rim and tire fit system, S1 series wheelsets are available in six different rim models, with internal widths ranging from 23mm to 38mm. Combined with Stan’s low-profile, high-volume Bead Socket Technology rim design, these widths let the new S1 range accommodate tires from 2-inch to 3.5-inch. All S1 wheelsets are built with 32 spokes front and rear, Sapim’s proven Race spokes, Secure Lock brass nipples, and Stan’s faster-engaging Neo hubs. Hubs are available to fit most axle systems, including Boost. The S1 series includes reinforced versions of the classic Crest, Arch, and Flow--names already familiar to fans of Stan’s tubeless rims. In addition to the Crest S1, Arch S1, and Flow S1, three entirely new wider wheelsets will be available. The Sentry S1, Baron S1, and Major S1 bring Stan’s patented Bead Socket Technology to Plus bikes. Flow S1 Wheelset - Use: Aggressive Trail, All Mountain, Enduro, and Downhill - Internal Rim Width: 29mm - Optimal Tires Size: 2.35 to 2.8-inch - Hubs: Stan’s Neo 32-hole Front, 32-hole Rear - Spokes/Nipples: Sapim Race Black 2.0/1.8/2.0mm, Secure Lock Brass Silver Nipples - Wheel Sizes and Weights: 27.5-inch (2,034g), and 29-inch (2,134g)
Learning from our very successful EWS riders, we designed the rims for the EXC 1200 SPLINE 35 to be tough enough for everything the best in the sport can throw at them yet light enough to spin all day. And, they're the right width to accommodate today's high-volume enduro tires. This rim is complemented by our completely new top-end Ratchet System hubs which maintain the lightweight theme, as do the bladed and butted straight-pull spokes. The result is any enduro rider's dream wheel: Peace-of-mind in the downhills and enough breath for a chat on the climbs. - SRAM XD MTB cassette-compatible
Page 1 of 15 Next page